SUPPORT > Titanium Grade in Different Co_ BAOJI QIYUEXIN TITANIUM METAL CO., LTD

GB		ASTM
TA1	Industrial pure titanium	GR1
TA1-1	Industrial pure titanium	GR1
TA2	Industrial pure titanium	GR2
TA3	Industrial pure titanium	GR3
TA4	Industrial pure titanium	GR4
TA8	Ti-0.05Pd	GR16
TA8-1	Ti-0.05Pd	GR17
TA9	Ti-0.2Pd	GR7
TA9-1	Ti-0.2Pd	GR11
TA10	Ti-0.3Mo-0.8Ni	GR12
TA17	Ti-4Al-2V
TA18	Ti-3Al-2.5V	GR9
TB5	Ti-15V-3Al-3Gr-3Sn	Ti-15333
TC4	Ti-6Al-4V	GR5
TC1	Ti-2Al-1.5Mn
TC2	Ti-4Al-1.5Mn
TC3	Ti-5Al-4V
TC10	Ti-6Al-6V-2Sn-0.5Cu-0.5Fe	Ti-662
TC24	Ti-4.5Al-3v-2Mo-2Fe
TA7	Ti-5Al-2.5Sn	GR6
TA11	Ti-8Al-1Mo-1V	Ti-811
TA15	Ti-6.5Al-1Mo-1V-2Zr

TITANIUM BENEFITS
High strength,
High resistance to pitting, crevice corrosion resistance,
High resistance to stress corrosion cracking, corrosion fatigue and erosion,
Cold bending for complex piping bends without fittings or flanges,
High strength to weight ratio,
Weight saving possibilities,
Low modulus, high fracture toughness and fatigue resistance,
Suitability for coiling and laying on seabed,
Ability to withstand hot/dry and cold/wet acid gas loading,
Excellent resistance to corrosive and erosive action of high-temperature acid steam and brine,
Good workability and weldability.
TITANIUM CHEMICAL COMPOSITION
Palladium (Pd) and Ruthenium (Ru), Nickel (Ni) and Molybdenum (Mo) are elements which can be added to the pure titanium types in order to obtain a significant improvement of corrosion resistance particularly in slightly reducing environments where titanium otherwise might face some problems due to insufficient conditions for formation of the necessary protective oxide film on the metal surface. The formation of a stable and substantially inert protective oxide film on the surface is otherwise the secret behind the extraordinary corrosion resistance of titanium.
The mechanical properties of commercially pure titanium are in fact controlled by “alloying” to various levels of oxygen and nitrogen to obtain strength level varying between approximately 290 and 550 MPa. For higher strength levels alloying elements, e.g. Al and V have to be added. Ti 3AL 2.5V has a tensile strength of minimum 620 MPa in annealed condition and minimum 860 MPa in the as cold worked and stress relieved condition. The CP-titanium grades are nominally all alpha in structure, whereas many of the titanium alloys have a two phase alpha + beta structure. There are also titanium alloys with high alloying additions having an entire beta phase structure. While alpha alloys cannot be heat treated to increase strength, the addition of 2.5% copper would result in a material which responds to solution treatment and ageing in a similar way to aluminum-copper.
TITANIUM DENSITY
Titanium is more then 46% lighter than steel. For comparative analysis, aluminum is approximately 0.12 lbs/cu.in, Steel is approximately 0.29 lbs/cu.in, and Titanium is approximately 0.16 lbs/cu.in.
TITANIUM CORROSION RESISTANCE
Titanium’s outstanding corrosion resistance is due to the formation of a tightly adherent oxide film on its surface. When damaged, this thin invisible layer immediately reforms, maintaining a surface which is completely resistant to corrosive attack in sea water and all natural environments. This oxide is so resistant to corrosion that titanium components often look brand new even after years of service.

PRODUCTS

SUPPOT